v7.9beta [testing] is released! |
您所在的位置:网站首页 › ospf router id conflict is detected on interface › v7.9beta [testing] is released! |
RouterOS version 7.9beta has been released on the "v7 testing" channel!
Before an upgrade:
1) Remember to make backup/export files before an upgrade and save them on another storage device;
2) Make sure the device will not lose power during upgrade process;
3) Device has enough free storage space for all RouterOS packages to be downloaded. What's new in 7.9beta4 (2023-Mar-23 15:01): Changes in this release: *) bgp - improved BGP VPN selection; *) bridge - added warning log when "ageing-time" exceeds supported hardware limit for 98DX224S, 98DX226S, and 98DX3236 switch chips; *) bridge - fixed FastPath when setting "use-ip-firewall-for-vlan" or "use-ip-firewall-for-pppoe" without enabled "use-ip-firewall"; *) certificate - fixed bogus log messages; *) chr - fixed public SSH key pulling when running on AWS; *) console - added "/task" submenu (CLI only); *) console - added option to create new files using "/file add" command (CLI only); *) console - improved stability when doing "/console inspect" in certain menus; *) console - improved stability when editing long strings; *) console - improved system stability; *) console - removed bogus "reset" command from "/system resource usb" menu; *) console - rename flag "seen reply" to "seen-reply" under "/ipv6 firewall connection" menu; *) console - show Ethernet advertise, speed and duplex settings depending on configured auto-negotiation; *) container - fixed invoking "container shell" more than once; *) container - improved "container pull" to support OCI manifest format; *) detnet - fixed interface state detection after reboot; *) dhcp - changed the default lease time for newly created DHCP servers to 30 minutes; *) dhcpv4-server - release lease if "check-status" reveals no conflict; *) disk - improved system stability when removing USB while formatting; *) ethernet - fixed half-duplex forced mode at 10Mbps and 100Mbps on ether1 for RB5009, Chateau 5G ax and hAP ax3 devices; *) filesystem - fixed partition "copy-to" function; *) firewall - added "connection-nat-state" to IPv6 mangle and filter rules; *) health - added limited manual control over fans for CRS3xx, CRS5xx, CCR2xxx devices; *) ipsec - fixed packet processing by hardware encryption engine on RB850Gx2 device; *) ipsec - refactor X.509 implementation; *) ipv6 - added "valid" and "lifetime" parameters for SLAAC IPv6 addresses; *) ipv6 - send out RA packet with "preferred-lifetime" set to "0" when IPv6 address is deactivated; *) l3hw - improved route offloading for 98DX224S, 98DX226S, and 98DX3236 switch chips; *) leds - disable LEDs after "/system shutdown"; *) lte - capped maximum lifetime of SLAAC address to 1 hour; *) lte - fixed CA band clearing on RAT mode change; *) lte - fixed duplicate IPv6 route for lte interface when "ipv6-interface" setting is used; *) lte - fixed LTE interface not showing up when resetting RouterOS configuration; *) lte - fixed passthrough mode when used together with another APN for Chateau 5G; *) lte - fixed R11-LTE-US in LTE passthrough mode; *) lte - fixed R11e-LTE-US reporting of RSSI in LTE mode; *) lte - fixed re-attach in some cases where module would stay in not-running state after network detach; *) lte - fixed second modem halt on dual R11e-LTE6 setup; *) mpls- fixed LDP "preferred-afi" parameter; *) netwatch - added "startup-delay" setting (CLI only); *) netwatch - improved ICMP status evaluation when no reply was present; *) netwatch - limit "start-delay" range; *) ospf - fixed processing of fragmented LSAs; *) ovpn - added support for OVPN server configuration export and client configuration import from .ovpn file; *) quickset - fixed displaying of "SINR" when value is 0; *) rose-storage - added option to nvme-discover with hostname (CLI only); *) rose-storage - fixed crash on nvme-tcp disable; *) rose-storage - fixed rsync transfer permissions; *) rose-storage - various stability fixes; *) route - fixed "dynamic-id" for VRF tables; *) route - improved system stability when making routing decision; *) route - show SLAAC routes under the "/routing route" menu; *) route-filter - improved stability when matching blackhole routes; *) routerboot - added "preboot-etherboot" and "preboot-etherboot-server" settings ("/system routerboard upgrade" required) (CLI only); *) sfp - added log warning about failed auto-initialization on RB4011, RB5009, CCR2004-1G-12S+2XS, CCR2004-16G-2S+, CCR2116-12G-4S+, CCR2216-1G-12XS-2XQ devices; *) sfp - allow modules that hold "TX_FAULT" high signal all the time on RB4011, RB5009, CCR2004-1G-12S+2XS, CCR2004-16G-2S+, CCR2116-12G-4S+, CCR2216-1G-12XS-2XQ devices; *) sfp - allow modules with bad or no EEPROM in forced mode on RB4011, RB5009, CCR2004-1G-12S+2XS, CCR2004-16G-2S+, CCR2116-12G-4S+, CCR2216-1G-12XS-2XQ devices; *) sfp - fixed "rate-select" functionality on CCR2004-16G-2S+ and CCR2004-1G-12S+2XS devices (introduced in v7.8 ); *) sfp - fixed combo-ether link monitor for CRS328-4C-20S-4S+ switch; *) sfp - improved module initialization and display more detailed initialization status on RB4011, RB5009, CCR2004-1G-12S+2XS, CCR2004-16G-2S+, CCR2116-12G-4S+, CCR2216-1G-12XS-2XQ devices; *) sfp - improved SFP28 interface stability with some optical modules for CRS518 switch; *) sfp - improved system stability with some SFP GPON modules on RB4011, RB5009, CCR2004-1G-12S+2XS, CCR2004-16G-2S+, CCR2116-12G-4S+, CCR2216-1G-12XS-2XQ devices; *) socks - added VRF support; *) ssh - added Ed25519 host key support; *) ssh - do not allow SHA1 usage with strong crypto enabled; *) ssh - improved service responsiveness when changing SSH service settings; *) ssh - improved SSH key import process; *) storage - mount RAM drive for devices with 32MB flash; *) supout - added DHCP server network section; *) switch - fixed ACL rules matching IPv6 packets when using only IPv4 matchers; *) switch - improved system stability for 98DX8208, 98DX8216, 98DX8212, 98DX8332, 98DX3257, 98DX4310, 98DX8525, 98DX3255, 98PX1012 switches; *) vrrp - added "self" value for "group-master" setting; *) vxlan - added forwarding table; *) vxlan - fixed packet drops when host moves between remote VTEPs; *) webfig - added inline comments; *) webfig - fixed "Destination" value under "MPLS/Forwarding-Table" menu; *) webfig - fixed issue where "Certificate" value disappears under "IP/Services" menu; *) webfig - fixed issue where entries might be missing under "IP/DHCP-Server" menu; *) webfig - various stability fixes; *) wifiwave2 - added "radio/reg-info" command to show regulatory requirements (currently implemented for 802.11ac interfaces) (CLI only); *) wifiwave2 - added ability to configure antenna gain; *) wifiwave2 - added ability to configure beacon interval and DTIM period; *) wifiwave2 - added information on additional interface capabilities to radio parameters; *) wifiwave2 - automatically add a VLAN-tagged interface to the appropriate bridge VLAN; *) wifiwave2 - exit sniffer command and return error when trying to sniff on an unsupported channel; *) wifiwave2 - fixed 802.11r roaming for clients that performed initial authentication with an AP which has been restarted since; *) wifiwave2 - fixed issue of some supported channels not being listed in the radio parameters; *) wifiwave2 - fixed issue which lead to VLAN-tagged wireless clients receiving tagged traffic from other VLANs; *) wifiwave2 - fixed VLAN tagging for unencrypted (open) APs; *) wifiwave2 - improved general interface stability; *) wifiwave2 - improved regulatory compliance for hAP ax^2, hAP ax^3 and Chateau ax; *) wifiwave2 - increased maximum value for "channel.frequency" to 7300; *) wifiwave2 - show information on captured packets and added ability to save them locally in a pcap file; *) winbox - added "MTU" and "Hoplimit" properties under "IPv6/Routes" menu; *) winbox - added "Preferred AFI" property under "MPLS/LDP-Instance" menu; *) winbox - added "S" flag under "IPv6/Firewall/Connections" menu; *) winbox - added "Tx Power" property under "Wifiwave2/Status" menu; *) winbox - added "Tx Queue Drops" property under interface settings "Traffic" tab; *) winbox - added "Username" and "Password" properties under "Container/Config" menu; *) winbox - added "Valid" and "Preferred" properties under "IPv6/Address" menu; *) winbox - added missing properties for "Remote ID Type" under "IP/IPsec/Identities" menu; *) winbox - changed route flag name from "invalid" to "inactive"; *) winbox - fixed "TLS" property under "Tools/Email" menu; *) winbox - fixed "Type" property under "System/Disk" menu when "rose-storage" package is installed; *) winbox - fixed default value for "Allow managed" property under "Zerotier" menu; *) winbox - fixed duplicate "My ID" column under "IP/IPsec/Identities" menu; *) winbox - fixed minor typo in "WifiWave2/Radios" menu; *) winbox - fixed missing "Sector Writes" for certain devices under "System/Resources" menu (introduced in v7.8 ); *) winbox - improved Ethernet advertise, speed and duplex settings; *) winbox - only show permitted countries for wifiwave2 interfaces; *) winbox - show missing "Designated Bridge" and "Designated Port Number" monitoring data under "Bridge/Port menu; *) www - allow unsecure HTTP access to REST API; *) x86 - fixed changing software-id (introduced in v7.7); *) zerotier - upgraded to version 1.10.3; To upgrade, click "Check for updates" at /system package in your RouterOS configuration interface, or head to our download page: http://www.mikrotik.com/download If you experience version related issues, then please send supout file from your router to [email protected]. File must be generated while a router is not working as suspected or after some problem has appeared on the device Please keep this forum topic strictly related to this particular RouterOS release. |
今日新闻 |
推荐新闻 |
CopyRight 2018-2019 办公设备维修网 版权所有 豫ICP备15022753号-3 |